Keg Dispensing Supplies

Chrome replacement bonnet for the Perlick Perl faucet.

Everyone with a draft system should own a spanner wrench! This little curved tool hooks into the holes on the faucet coupler to loosen or tighten your faucet as needed. Even if you bought a draft system preassembled, you will still want to take the faucet off and clean it periodically to ensure the cleanest pour possible.

Standard faucets are just that...standard faucets for pouring beer! They come standard with a number of kegerators and dispensing setups, and can be found on jockey boxes, homemade beer fridges and keezers, just about anywhere you find beer! Economical, they are easy to take apart and clean, with just a few moving parts that can easily be replaced if needed. These make great replacement faucets for damaged faucets on existing setups, or work well on new installations as well! These can be put on the end of a shank for a new installation.

Superflush Tap & Line Cleaner is an safe, easy-to-use, economical and biodegradable line cleaner perfect for use on kegerators and draft dispensing systems. Simply mix 2-3 oz. with 1 gallon water as per the instructions and pump through lines. Allow to sit in lines for a few minutes, then flush clean with water. A solution made at the same rate may be used to clean faucet and coupler parts as well. Sold in a 32 oz bottle, Superflush can help you keep your lines pristine, pouring perfect beer every time!

A 4-way manifold is the perfect way to carbonate four kegs at once, or to pressurize kegs and run a Blichmann BeerGun at the same time! The CO2 can be hooked up from the regulator via the barb on the side of the manifold using standard 5/16" ID Bevlex tubing, and the other barbs can be run with the same tubing to gas disconnects for carbonating and dispensing from kegs, or to other CO2 driven devices. When mounted, the barbs run straight downward. Includes shutoff valves on the four top barbs on the manifold, which give another level of protection from lost CO2!

This is a replacement faucet end washer for standard faucets. This washer fits on the end of the faucet that attaches to the shank on a kegerator setup and helps create a good seal, ensuring no liquid leaks out. From time to time, these wear out and need to be replaced. Luckily, Great Fermentations has the replacement washer you need!

This is the part that really gets the beer flowing! Chrome-plated brass construction ensures for longevity of the coupler, so that you can keep the beer flowing keg after keg. This "D" style coupler is the standard coupler used by virtually all American and Canadian breweries, and as such, this is the most convenient keg coupler to own in North America. One of these allows you to tap almost any keg from any American or Canadian breweries. This coupler comes with a standard 5/16" gas barb, check valve and beer nut on the gas side. Not included with this coupler are the neoprene washer, 3/16" barb liquid tailpiece and beer nut.

This is a replacement white plastic lever shaft washer for standard faucets. It goes on top of the ball of the faucet lever of a standard faucet. Washers wear out over time, and used equipment that has not been properly maintained may need new washers. If this is the case, Great Fermentations has replacements for you!

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the male side that has a black gasket that allows it to quickly connect to the female end. It has a 3/8" straight barb to hook up to 3/8" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This male piece is used with the Female 3/8"In-line Hose Barb, item #05P01-121.

Party Pig Gasket

This is a washer for the plunger assembly in a standard faucet. It works well as a replacement for the washer on a plunger assembly, should yours go missing or damaged. Keep those seals tight and the beer flowing!

Turn your fridge into a kegerator with our kegerator homebrew kegging system! This system comes with all the internal workings of a kegerator system you will need, except the CO2 cylinder.

Included is a high quality Taprite regulator, ball lock gas line assembly, a used 5 gallon cornelius keg, a ball lock liquid disconnect with swivel nut set, 6 feet of 3/16" ID Bevlex thick-walled liquid tubing, and a full shank assembly that includes a standard beer faucet, faucet knob, 4" shank, 1/4" tailpiece, beer nut and neoprene washer. Make the draft system you have always wanted with this kegerator kegging system!

All you'll need in addition to this kit to make the ultimate kegerator, is a full CO2 tank. For local customers we sell full tanks at all of our retail locations!

Have you ever damaged a gauge on your CO2 regulator? We've got the replacements you need! This is a left-hand threaded replacement tank pressure gauge for your CO2 regulator. These come standard on dual gauge regulators, and this one works with regulators that take a left-hand threaded gauge.

Party Pig Hi-Flow Activation Pump

If you have a sanke coupler that you would like to use with a pump instead of CO2, you need some sort of adapter...like this one! This will allow you to adapt a standard sanke coupler to a beer pump so that you can pump and serve! Simply screw on to the gas side of your coupler, then screw on your pump. It's as simple as that! Get your beer flowing with a pump and this adapter.

Protect regulator gauges from damage. Bolts hold metal protectors on either side of the regulator. Works with all regulators manufactured by Norgren, Tap Rite and most Micro Matic and NADS.

Turn any pumpkin into a keg

Pumpkin kegs are great for pumpkin brews

Watermelon kegs for summer Wits and Lagers

Pumpkin tap kit includes a black faucet knob

3 inch shank