Keg Dispensing Supplies

The following beer keg dispensing equipment allows you to dispense and serve homebrew without all the hassle of bottles. Choose from homebrew kegerators, homebrew keg dispensing systems or portable homebrew setups.

Showing 21 products

Low Profile Sanke Coupler

Get that coupler into your kegerator! Some kegerators don't have a lot of clearance space, and a standard keg coupler won't fit on top of the keg. The solution to this problem? A low-profile sanke coupler! This coupler measures a mere 3.25", taking up less space above your keg than normal couplers. It has a unique design by which the engaging mechanism twists down the body and engages into the keg. Above the engaging body, the CO2 comes in the sideways barb, and liquid flows out sideways as well. Perfect for kegerator setup without a lot of vertical room! This coupler comes with an integrated gas barb. Not included is a 3/16" liquid tailpiece, beer nut and neoprene washer.

GF_07S07-135
$79.99

Bass Sanke "G" Style Coupler

The "G" type coupler is sometimes known as a Bass keg coupler or tap. This is the style of coupler used on Bass, Boddington's, Anchor, Grolsch, Old Speckled Hen, Innis & Gunn and Watney's kegs, among others. Without this style of coupler, it may be hard to get beer out of kegs from those breweries! This coupler comes with the gas side connections, but does not come with the 3/16" liquid tailpiece, beer nut or neoprene washer needed for the liquid side.

GF_07S07-112
$79.99

Taprite Regulator Repair Kit

If the diaphragm goes out on your Taprite regulator goes out, there's nothing left to do but get a whole new regulator, right? Not anymore! Great Fermentations brings you this regulator repair kit that comes with the parts and instructions you need to fix your regulator. Much cheaper than buying a whole new regulator, give this kit a try!

GF_03C09-101
$19.99

1/2" ID Bevlex Tubing

This Bevlex tubing measures 1/2" inner diameter, making it perfect for use with a 1/2" racking cane or large auto-siphon. The thicker walling is kink-resistant, and is perfect for more rigorous applications. Some people have been known to use this tubing for racking using a vacuum pump, and others just prefer it to thin-walled tubing because of its durability. Whatever you use it for, we've got it here for you!

Inner Diameter: 1/2 in.
Outer Diameter: 3/4 in.

GF_08A05-127
$0.99

3/16" Tailpiece

This 3/16" tailpiece works with standard 3/16" ID liquid side tubing in a range of liquid dispensing applications. Most commonly, this tailpiece is used with a beer nut and a neoprene beer washer on the end of a shank as part of a faucet draft system. However, they are also used on sanke couplers for the liquid dispensing side. They can come in quite handy when replacing preinstalled liquid side connections in kegerators.

GF_05C08-130
$1.49

Faucet (spanner) Wrench

Everyone with a draft system should own a spanner wrench! This little curved tool hooks into the holes on the faucet coupler to loosen or tighten your faucet as needed. Even if you bought a draft system preassembled, you will still want to take the faucet off and clean it periodically to ensure the cleanest pour possible.

GF_20B03-125
$3.99

Beer Nut

Beer nuts are a standard hex nut used on many beer dispensing connections. Most notably, they are used on the end of faucet shanks and on sanke couplers. They accept a standard tailpiece, such as a 3/16" tailpiece for liquid applications or a 5/16" tailpiece for CO2 applications. In addition, neoprene beer washers are also used in conjuction to create a seal. These are nickel plated brass hex nuts with a 7/8" x 14 straight pipe thread that is standard in the U.S. beer industry. Always keep a few of these on hand for any situation that may arise!

GF_04B03-135
$1.89

Faucet Plug w/Brush

Brilliant! A small brush that fits over the end of your cap and kills two birds with one stone: keeps your faucet clean, and keeps flies out! When the heat of summer comes around and old beer heats up in the metal interior of your faucet, flies start hovering around. And what is worse than getting a cup of beer full of flies? Protect your beer by having a faucet plug with brush that scrubs out the inside of your tap and keeps flies out!

GF_12C09-100
$1.99

Nitrogen Tank Adapter for CO2 Regulator

Use your CO2 regulator with a beer gas tank with this CO2 regulator to nitrogen adapter! This part is approximately 3 inches long and will adapt a female CGA-320 fitting (which is the standard fitting on a standard CO2 regulator) to a male CGA-580 fitting (which is the standard fitting on a beer gas tank). This way, you will be able to use your existing CO2 regulator on a beer gas tank without buying a new nitrogen regulator! This works great for the creamy beer enthusiast who occasionally uses beer gas! Please note that this connection should NOT be used with pure nitrogen due to the higher pressures that pure nitrogen is kept under. This should work great for most people who occasionally use beer gas to give their beers that extra creaminess!

GF_02F08-101
$29.99

Taprite Dual Gauge Regulator w/Large Knob

Taprite has long been a trusted name in the beverage industry. Known for their high quality craftsmanship, Taprite has one of the best regulators on the market! These dual guage regulators have a low pressure gauge which shows output pressure (supports 0 - 50 PSI), and a high pressure gauge that shows the remaining pressure in the cylinder. Taprite regulators are known for having high quality diaphragms which stand up to the test of time much better than cheaper or lower-quality regulators, as well as being more accurate for a longer period of time. The regulator also includes a standard CO2 barb with shutoff valve and a safety check.

GF_03C09-102
$64.99

O-ring Replacement Set

Change out all your standard o-rings on a cornelius keg with this o-ring replacement set! This comes with one center closure o-ring, two post o-rings, and two dip tube o-rings. These are all the standard o-rings that come on a Cornelius keg. Change these out periodically, when your connections get hard to make or when your o-rings begin to fray. Always handy to have on hand in case of a kegging emergency!

GF_GF206
$3.99

Crimper for Oetiker (Ear) Clamp

Do you use a lot of Oetiker clamps to tighten your connections? Or would you like to switch your connections over to Oetiker style and have a more permanent clamp on your liquid and gas connections? A crimper of your own would come in extremely handy! While oetiker clamps can be crimped with a set of pliers, the crimping can be difficult and uneven. This crimper clamps Oetiker-type clamps down with ease and precision, ensuring a perfect crimp every time! A must-have for anyone doing projects that use Oetiker-style clamps!

GF_C100
$13.99

Oetiker (Ear) Clamp - No. 157

Oetiker clamps provide a permanent clamping solution! This style of clamp has a 1-ear design, which means they are crimped at a single point on the clamp to create a superior seal over your tubing. These large Oetiker clamps are often used on 5/16" thick-walled tubing that is used in CO2 connections on kegging and draft systems. These clamps hold tight, creating a great seal that holds for a long time! Some people prefer these for more permanent systems. If you are looking to switch over to a snug seal that lasts, make sure you use Oetiker clamps!

GF_06G08-146
$0.69

Regulator Gauge - Tank Pressure RHT

Have you ever damaged a gauge on your CO2 regulator? We've got the replacements you need! This is a right-hand threaded replacement tank pressure gauge for your CO2 regulator. These come standard on dual gauge regulators, and this one works with regulators that take a right-hand threaded gauge.

GF_03G07-219
$10.99

Regulator Gauge - Output Pressure RHT

Have you ever damaged a gauge on your CO2 regulator? We've got the replacements you need! This is a right-hand threaded replacement output pressure gauge for your CO2 regulator. It measures output pressure between 0 and 60 PSI and works with regulators that take a right-hand threaded gauge.

GF_03G07-142
$9.99

Stainless Steel Kegerator Homebrew Kegging System - New Keg

Turn your fridge into a kegerator with our kegerator homebrew kegging system! This system comes with all the internal workings of a kegerator system you will need, except the CO2 cylinder.

Included is a high quality Taprite regulator, ball lock gas line assembly, a brand new 5 gallon cornelius keg, a ball lock liquid disconnect with swivel nut set, 6 feet of 3/16" ID Bevlex thick-walled liquid tubing, and a full stainless steel shank assembly that includes a SS standard beer faucet, faucet knob, 4" SS shank, 1/4" tailpiece, beer nut and neoprene washer. Make the draft system you have always wanted with this kegerator kegging system, complete with a brand spankin' new keg and stainless steel serving equipment!

All you'll need in addition to this kit to make the ultimate kegerator, is a full CO2 tank. For local customers we sell full tanks at all of our retail locations!

GF_GF801SS
$279.99

Stainless Steel 5/16" x 5/16" Splicer

This stainless steel splicer has 5/16" splicers on both sides. It can be used to connect two lengths of hose with a 5/16" ID together. This is a standard size for liquid siphon line, but these fittings can be used in gas applications as well.

GF_05A03-125
$2.49

US Sanke "D" Coupler

This is the part that really gets the beer flowing! Chrome-plated brass construction ensures for longevity of the coupler, so that you can keep the beer flowing keg after keg. This "D" style coupler is the standard coupler used by virtually all American and Canadian breweries, and as such, this is the most convenient keg coupler to own in North America. One of these allows you to tap almost any keg from any American or Canadian breweries. This coupler comes with a standard 5/16" gas barb, check valve and beer nut on the gas side. Not included with this coupler are the neoprene washer, 3/16" barb liquid tailpiece and beer nut.

GF_07S07-102
$31.99

6" Shank with 3/16" Bore

Beer shanks to make all your dispensing dreams come true! These chrome plated brass shanks are used in a variety of setups to create draft systems. A 3/16" bore is perfect for liquid dispensing of all types, including sweet sweet beer. This 6" shank (actual measurement: 6 1/8") is longer than the standard 4" shank and works when you need just a little more length. Simply drill out your hole, place your shank through, and lock in place with the included lock nut. A faucet can then be attached to the outside of your draft setup, whether it be a kegerator, keezer or jockey box! Also needed on the inside is a 3/16" tailpiece, neoprene beer washer and beer nut.

GF_12K09-105
$24.99

74 gram CO2 Bulb

The Flex Tap is the perfect system for dispensing beer out of sanke kegs, and we have the replacement CO2 bulbs to run it! These 74 gram CO2 bulbs will typically work to dispense 7.5 gallons of beer, meaning that you can do about half of a full 1/2 barrel keg with one bulb. Be sure to have extras on hand!

GF_50502
$11.99

Gas Ball Lock Disconnect - 1/4" MFL

You can never have too many disconnects! For all your ball lock draft needs, Great Fermentations offers you these gas ball lock disconnects. Easy to take apart and clean, these are used with 5/16" ID Bevlex tubing on manifolds and splitters to carbonate multiple kegs at once. These disconnects have a 1/4" MFL connection, which is perfect for attaching a swivel nut set for myriad applications. They have a plastic end on the male flare fitting so you don't have to use a plastic flare fitting washer when connecting them to metal. Make sure you have enough on hand for all the kegging and draft projects your mind can come up with!

GF_07C07-115
$6.99

Showing 610 - 630 of 668 results