Keg Dispensing Supplies

A Y-shaped connector used to split CO2 from a regulator that only has one outlet to two. Measurements are 1/4" MPT X 1/4" FPT X 1/4" FPT. Perfect for use in sending CO2 to both a keg and the Blichmann BeerGun at the same time! Also useful in other applications when CO2 needs to be split two ways.

Make your coonecitons tight! With this grommet, you can create the perfect seal for your liquid tower elbow. This will allow the beer to continue flowing freely for years to come!

Make your dream draft system at home! Our standard faucet assembly includes everything you will need to put a faucet on an old fridge, or on the collar of a chest freezer.

This standard assembly includes:
Standard chrome-plated faucet
Faucet knob
Chrome-plated 4 1/8 in. shank with 3/16 in. bore
Beer nut, neoprene washer and 3/16 in. tailpiece

Simply drill your hole, install your assembly, and hook your liquid line into the 3/16 in. tailpiece in the back of the assembly, and you'll be pouring draft beer in no time! Perfect for refrigerator or chest freezer conversions. Get a few and have multiple beers on at once!

This 5/16" tailpiece works with standard 5/16" ID CO2 tubing. Most often, these are found on the CO2 side of sanke couplers. Used in conjunction with a beer nut and a neoprene beer washer, these tailpieces can create a tight seal for CO2. Useful as a replacement on kegerator setups, make sure you have one on hand in your draft emergency kit!

Is your tap handle too short? Not visible or prominently displayed, like you would like? Look no further than this chrome extension to solve your tap handle woes! This 1-inch chrome extension is placed between your faucet and tap handle to extend it outwards. Simple to use and effective, get the right length for your tap handle today!

A 4-way manifold is the perfect way to carbonate four kegs at once, or to pressurize kegs and run a Blichmann BeerGun at the same time! The CO2 can be hooked up from the regulator via the barb on the side of the manifold using standard 5/16" ID Bevlex tubing, and the other barbs can be run with the same tubing to gas disconnects for carbonating and dispensing from kegs, or to other CO2 driven devices. When mounted, the barbs run straight downward. Includes shutoff valves on the four top barbs on the manifold, which give another level of protection from lost CO2!

Rustproof wrench for CO2 nut on regulator. The right wrench, right where you need it, when you need it.

A swivel nut set with a barb for your gas side connections! These swivel nut sets come with a standard 1/4" female flared nut and a 5/16" barb that can be used with standard 5/16" ID gas tubing. These can be connected directly to the standard liquid disconnects that we offer, or used with a plastic flare fitting for any direct metal-on-metal connections.

A bent tailpiece can come in extremely handy when connecting liquid lines in hard-to-reach places, such as kegerator towers or homemade keezers and kegerators. Not only that, but a 90 degree bend just makes sense in some setups! This tailpiece has a standard 3/16" barb, perfect for liquid line applications. It is often used with a beer nut and a neoprene beer washer for a secure seal.

Always have a tap when the party demands one! This economy twist sanke pump tap is a classic party-style pump coupler. It features a pump for pressurizing a keg with air, a twist-style coupling mechanism similar to those found on low-profile sanke couplers, and a short black picnic faucet. This is the perfect, economical solution for kegs that are going to be quickly consumed. Instead of paying the liquor store multiple deposits, invest in a pump tap and always be prepared to get the party started!

Replace your missing or damaged coupling nut with one of these brass replacements from Great Fermentations! These also work well with a faucet adapter (item #17C13-100). Put one of these on the faucet adapter, add a faucet and a liquid disconnect on the other end, and you have yourself a faucet assembly ready to put on a cornelies keg!

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the female side that has a gray disconnect button for quickly disconnecting from the male end. It has a 3/8" straight barb to hook up to 3/8" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This female piece is used with the Male 3/8" In-line Hose Barb, item #05P01-123.

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the male side that has a black gasket that allows it to quickly connect to the female end. It has a 1/4" straight barb to hook up to 1/4" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This male piece is used with the 1/4" Quick Disconnect Body, item #05P01-120.

From Taprite comes this "S" style keg coupler, also known as a tap. This is the part that really gets the beer flowing! Chrome-plated brass construction ensures for longevity of the coupler, so that you can keep the beer flowing keg after keg. The "S" style coupler is a common European style coupler used by many leading breweries in Europe, including Stella Artois, Heineken, Beck's, Amstel, Newcastle, Pilsner Urquell, Lindeman's, and Huyghe, makers of Delirium Tremens. It is similar to a North American "D" style coupler, but runs about a 1/4" deeper into the keg. This coupler comes with a standard 5/16" gas barb, check valve and beer nut on the gas side. Not included with this coupler are the neoprene washer, 3/16" barb liquid tailpiece and beer nut.

Get that coupler into your kegerator! Some kegerators don't have a lot of clearance space, and a standard keg coupler won't fit on top of the keg. The solution to this problem? A low-profile sanke coupler! This coupler measures a mere 3.25", taking up less space above your keg than normal couplers. It has a unique design by which the engaging mechanism twists down the body and engages into the keg. Above the engaging body, the CO2 comes in the sideways barb, and liquid flows out sideways as well. Perfect for kegerator setup without a lot of vertical room! This coupler comes with an integrated gas barb. Not included is a 3/16" liquid tailpiece, beer nut and neoprene washer.

Want to pour the perfect stout or nitro beer every time? With the stout faucet assembly, you'll be able to add a stout faucet to your kegerator that pours a rich, creamy head on all nitrogenated or beer gas beers. Perfect for Guinness or Guinness clone beers, but can be used with a range of beer gas beers or beers on nitro, such as the nitrogenated IPAs and Imperial Red Ales that have become popular as of late.

Assembly Includes the Following:
Stout faucet (Chrome plated body with a stainless spout and stainless restrictor plate).
Faucet knob
Chrome-plated 4 1/8 in. shank with 3/16 in. bore
Beer nut, neoprene washer and 3/16 in. tailpiece

Get this assembly, add it to your kegerator or keezer system, and impress all your friends with perfect pours every time!

If the diaphragm goes out on your Taprite regulator goes out, there's nothing left to do but get a whole new regulator, right? Not anymore! Great Fermentations brings you this regulator repair kit that comes with the parts and instructions you need to fix your regulator. Much cheaper than buying a whole new regulator, give this kit a try!

A brass regulator stem is the part that protrudes out from your regulator and attaches, via a regulator nut, to your CO2 cylinder. This is a left-hand threaded stem which should work on most standard CO2 regulators that take a left-hand thread. This works wonderfully as a replacement if your regulator stem is damaged or missing!

Simply put, this is a check valve ball. It works with standard NADS American "D" sanke couplers, as well as other sanke couplers that use the same ball. This helps to keep your beer in "check" by blocking backflow of liquid back through the valve. In some instances, people will lose the ball while cleaning the coupler. If this happens, never fear! We've got a replacement for you so you can keep that beer safely flowing!

Everyone with a draft system should own a spanner wrench! This little curved tool hooks into the holes on the faucet coupler to loosen or tighten your faucet as needed. Even if you bought a draft system preassembled, you will still want to take the faucet off and clean it periodically to ensure the cleanest pour possible.