Keg Dispensing Supplies

Beer shanks to make all your dispensing dreams come true! These chrome plated brass shanks are used in a variety of setups to create draft systems. A 3/16" bore is perfect for liquid dispensing of all types, including sweet sweet beer. This 5" shank (actual measurement: 5 1/8") is slightly longer than the standard 4" shank and works when you need just a little more length. Simply drill out your hole, place your shank through, and lock in place with the included lock nut. A faucet can then be attached to the outside of your draft setup, whether it be a kegerator, keezer or jockey box! Also needed on the inside is a 3/16" tailpiece, neoprene beer washer and beer nut.

Finally, a standard faucet made of above-standard material! These standard faucets are anything but standard, with full stainless steel bodies and levers. Stainless steel is the holy grail of beer materials! Sleek and stylist, it not only looks great, but is durable and will last longer than chrome or brass faucets. The simple design means that the faucets are easy to take apart and clean. For beer faucets that will last longer, stainless steel faucets can't be beat!

Just what the party ordered! A black picnic tap on one end of a 4-foot length of 3/16 in. ID thick walled tubing and a ball lock disconnect with 3/16 in. swivel nuts on the other. Both ends are attached with oetiker-style clamps, which have been crimped on for a tight connection! Be the life of the party by bringing this (and a full keg) to the next get-together!

This is a replacement chrome bonnet for standard faucets. It screws directly onto the faucet body, keeping the faucet lever and two washers in place. An excellent replacement for missing or damaged bonnets on standard faucets!

This stainless steel tee is perfect for gas application, but can be used wherever a tee with hose barb fittings is required. It has three 3/8" barb connections, one on all ends, and is therefore able to split gas off in two separate directions from the source.

Do you have a home draft system and use both a sanke coupler and ball or pin lock kegs? Instead of going through the routine of disconnecting your sanke coupler and reattaching ball or pin lock connections every time, make your life easier with a few of these tailpieces! They have a 1/4" MFL connnection and can be used in conjunction with a hex beer nut and a neoprene washer on both the gas and liquid side of your sanke coupler. Simply replace your existing tailpieces with these, and hook up the respective swivel nuts to your gas and liquid lines.Whenever you want to use sanke or ball/pin lock connections, you can easily attach the swivel nuts to either setup!

Please Note that we recommend using a flare fitting washer on the sanke side to completely seal the metal-on-metal connections (most modern ball and pin lock disconnects have plastic on the end of their connection, so a flare fitting washer is uneccessary unless you have an older style disconnect.) Make life easier for yourself and serve beer through any type of connection!

A great, easy way to make CO2 and keg connections!The pin lock gas dispensing kit is a 3-foot length of 5/16" ID Bevlex tubing with a ball lock gas disconnect and 5/16" swivel nut set worm-clamped on one end, and a small worm clamp on the other that can be used to connect the assembly to a CO2 manifold or regulator. Always good to have around, especially for carbonating several kegs at once!

Party Pig Pressure Pouch

This CO2 shutoff with barb and check valve is ideal for use with CO2 regulators and manifolds! It has 1/4" MPT right-hand threading on one side that threads into most standard regulators and manifolds. On the other end is a standard 3/8" barb, which works perfectly with standard CO2 gas line. Get one of these to replace a damaged or missing shutoff, put on a wye splittler, or create your own CO2 apparatus!

This 3/16" tailpiece works with standard 3/16" ID liquid side tubing in a range of liquid dispensing applications. Most commonly, this tailpiece is used with a beer nut and a neoprene beer washer on the end of a shank as part of a faucet draft system. However, they are also used on sanke couplers for the liquid dispensing side. They can come in quite handy when replacing preinstalled liquid side connections in kegerators.

A bonnet angler is a little piece that comes in handy when trying to use an extra-long tap handle on a kegerator that has a flat surface, such as a converted refridgerator. Often, a longer tap handle won't have the clearance necessary, and will hit the body of the kegerator, not able to fully shut the beer faucet. Alleviate these problems with a bonnet angler! The bonnet angler creates a slight forward lean, giving you room to proudly display your long tap handles!

A 4-way manifold is the perfect way to carbonate four kegs at once, or to pressurize kegs and run a Blichmann BeerGun at the same time! The CO2 can be hooked up from the regulator via the barb on the side of the manifold using standard 5/16" ID Bevlex tubing, and the other barbs can be run with the same tubing to gas disconnects for carbonating and dispensing from kegs, or to other CO2 driven devices. When mounted, the barbs run straight downward. Includes shutoff valves on the four top barbs on the manifold, which give another level of protection from lost CO2!

This is a replacement plunger shaft assembly for standard faucets. It joins with the faucet lever and moves back and forth to allow beer to flow from the faucet. If you need a replacement for an old standard faucet, Great Fermentations has one for you!

Individual 16 gram Co2 non-threaded bulb for use with our Cornelius Keg CO2 Charger (Item # 4990)

Simply put, this is a check valve ball. It works with standard NADS American "D" sanke couplers, as well as other sanke couplers that use the same ball. This helps to keep your beer in "check" by blocking backflow of liquid back through the valve. In some instances, people will lose the ball while cleaning the coupler. If this happens, never fear! We've got a replacement for you so you can keep that beer safely flowing!

Gas lost in your CO2 system can lead to a shorter life span of your CO2 cylinders. Prevent CO2 loss with a washer! A plastic CO2 washer fits between your CO2 cylinder and regulator and helps to create a good seal. A good seal ensures that you don't lose gas when carbonating or serving. These plastic CO2 washers fit Taprite brand regulators, as well as many standard-sized CO2 regulators. Keep a few on hand in case of an emergency!

Smooth and straight! This flange for the inside of your beer tower is made of black plastic. It is curved on one side to fit the curvature of the beer tower. The lock nut can be tightened up against the flange in order that everything is straight on your kegerator! These flanges sometimes get damaged or lost. This flange is the perfect replacement for most flanges on standard sized beer towers.

This is a replacement brass lock nut for the shank on your tower. It works perfectly well on most standard tower shanks used in beer towers. If you need a replacement, we've got one for you right here!

This Bevlex tubing measures 1/2" inner diameter, making it perfect for use with a 1/2" racking cane or large auto-siphon. The thicker walling is kink-resistant, and is perfect for more rigorous applications. Some people have been known to use this tubing for racking using a vacuum pump, and others just prefer it to thin-walled tubing because of its durability. Whatever you use it for, we've got it here for you!

Inner Diameter: 1/2 in.
Outer Diameter: 3/4 in.